Instalação *

Windows: descarregar o cliente em https://memorycoin.org e instalar. Os ficheiros do utilizador, incluindo a carteira wallet.dat, encontram-se em %appdata%MemoryCoin.

OS X: as instruções de instalação podem ser consultadas aqui. Os ficheiros do utilizador, incluindo a carteira wallet.dat em ~/Library/Application Support/Memorycoin.


Primeira utilização *

1 - wallet start

Esta é a nova versão da carteira MemoryCoin. O cliente necessita de descarregar a cadeia de blocos (para registar todas as transacções), pode verificar a evolução na barra de estado. A operação de descarga poderá demorar algum tempo, dependendo da velocidade de ligação à Internet.


Encriptação da carteira *

O primeiro passo é encriptar a carteira. Deverá proteger a carteira com uma senha bastante forte (várias palavras e que não sejam fáceis de adivinhar, não utilize palavras de livros ou filmes, mas algo que consiga memorizar. Adiciona pontuação, números e caracteres especiais para aumentar a segurança.)

Ir até ao menu “Settings” e escolher a opção de encriptação.

3 - encrypt

3.1 - encrypt 2

Será necessário introduzir a senha duas vezes, para ter a certeza que está correcta.

3.2 - encrypt 3

O cliente mostra novamente uma aviso para memorizar a senha. Afinal chama-se MemoryCoin !

3.3 - encrypt 4

O cliente encerrará e será necessário iniciar novamente a aplicação.

3.4 - encrypt 5

A carteira está agora devidamente encriptada, conforme indica o cadeira no inferior direito. A partir de agora após podem ser enviadas moedas após introdução da senha.

3.5 - encrypt 6


Cópia de segurança da carteira *

Agora que a carteira está encriptada é possível exportar e guardar num lugar seguro. “Seguro”, mas é provavelmente uma boa ideia para guardar cópias em vários lugares. ;)

4 - backup

Escolha a opção de backup no menu ‘File’ e especifique o caminho onde pretende guardar a carteira. Quando, mais tarde, pretender restaurar a carteira o ficheiro deverá ter o nome de wallet.dat. Se entretanto utilizar outras criptomoedas baseadas no bitcoin poderá alterar o nome do ficheiro da carteira um nome mais sugestivo (ex: wallet_mmc.dat)

Este ficheiro contém todas as informações necessárias para recuperar a carteira com o saldo actual de MemoryCoins. Para importar a carteira wallet.dat apenas é necessário guardar o ficheiro na pasta de instalação e iniciar o cliente.

Tente importar a carteira (altere wallet.dat para outro nome, dentro da pasta actual) antes de prosseguir – para ter certeza que o backup funciona!


Mineração *

Com o MemoryCoin é mais fácil para que todos participar no processo de mineração.

A mineração individual é pura uma autêntica lotaria. Se tiver bastante sorte e conseguir encontrar um bloco, a recompensa será toda sua. Não terá que partilhar com mais ninguém.

Se pretender obter uma pequena e constante recompensa de MMC, escolha uma lista de mineração em comunidade.

8 - mine

Está configurado para funcionar com MMCPool, e poderá sempre consultar o estado actual de mineração utilizando a função ‘Pool Balance’ (MMCPool).

Aparece então uma nova janela contendo a aplicação de mineração

8.1 - mine

It mines for the developer of the mining software for a while, after that your shares will get submitted to the pool and you start building up a balance.


Receber MMC *

So of course you want some coins now!

While you are waiting for your first mining income to arrive, there are several other options to get hold of some. Try the faucet, keep your eyes open for a giveaway, find a way to contribute and get a bounty or a tip, or just buy them on bter.com

In all cases, everything you need is your wallet address.

5 - receive

You could create more addresses, but this is not recommended. Because of MemoryCoin’s feature to vote for an executive board, weigthed by the balance of your main address, you should stick to one address to receive all your coins. You can’t really decide which address you vote from, so if you use several addresses you can not be sure whether your votes are counted with most possible impact. For further details read the advanced voting how-to.

Right-click the address to copy it to your clipboard and give it to the one who will send you coins. After a short while, you will notice a change on your wallet overview

5.1 - receive

Got your first coins! But it says unconfirmed… Have a look at the transactions tab
5.2 - receive

Here’s an overview of all transactions to or from your wallet. The questionmark means that no block was found since your transaction. After some minutes this changes to a clock, which indicates how many blocks have been found since the transaction.

5.3 - receive

You can be pretty sure that the transaction is valid after the first confirmation (and it’s shown as balance from then on), the clock changes to a check after 6 confirmations (~30 minutes), indicating that the transaction is definitely fine.

5.5 - receive


Enviar MMC *

Now that you got some MemoryCoins you can of course send them to others.

6 - send

You need to enter a recipient, which is the address where you want to send the coins. In the next field, you can give that address a name to store it to your address book. And of course you need to enter the amount you want to send.

6.1 - send

I chose to use my candidate’s address for the example. Sending 0.00000001 MMC to an address starting with MVTE is a vote for an officer position. This is explained in detail later on.

You can combine multiple sends by adding more recipients with the button on the bottom left. After making sure you typed in the correct data, hit send. A security message makes you confirm again.

6.2 - send

Now you will need the passphrase for authorization

6.3 - send

Sending MMC requires a transaction fee which is determined by the size of your transaction. Expect something around 0.01$ in MMC.

6.4 - send

And that’s it, you sent some coins on their way.

6.5 - send

You can watch your transaction getting confirmations in the transactions tab if you like

6.6 - send


Votação *

As mentioned before, by sending Satoshis to a candidate you can vote for him or her to get a position in the MMC executive board.

The new client has an own tab for voting, you just need to select the preference and enter the candidate’s address.

7.1 - vote

This will send 1 Satoshi for your first preference, 2 for the second, 3 for the third… When your first preference is eliminated while counting votes your whole vote is transferred to the second preference, and so on.

Voting requires a transaction fee like described in the “Enviar MMC” section.

Additionally there are some options to check your voting status:

7 - vote

– Current Voting Preferences: shows the candidates your votes are counted for

– Current Candidates: leads to the list of candidates for the different positions

– How To Vote: leads to the advanced how-to vote on this site

– Latest election results: shows an overview of the last election counts